ARCH - Combat bolt question...

[Fearghus]

Sorry max draw length. From where the string rests on the nock to the base
of the combat head

Ld Fearghus MacKenna
Deputy Earl Marshal for Archery Ansteorra
Man at Arms to Centurion Airaklee Wolf

----- Original Message -----
From: Bob Dewart <gilli at seacove.net>
To: <ansteorra-archery at ansteorra.org>
Sent: Friday, June 23, 2000 4:36 PM
Subject: Re: ARCH - Combat bolt question...


> Greetings and Hi There
>
> Are you changing  the max length of the arrow to 28 inches?  Before it was
a
> max draw length of 28 inches, which isn't the same thing.  The max draw
> length is measured from where the string rests to the base of the combat
> head.
>
>
> 5.   Maximum allowable draw length (bottom of the nock slot to just behind
> the blunt) is    28 inches.
>
> Gilli
> -----Original Message-----
> From: Duke, Wes <WDuke at healthaxis.com>
> To: 'ansteorra-archery at ansteorra.org' <ansteorra-archery at ansteorra.org>
> Date: Friday, June 23, 2000 10:33 AM
> Subject: RE: ARCH - Combat bolt question...
>
>
> >1. While the rules do state that UHMW is legal on wood shafted arrows,
> >I have not tried this, but will. I may change the wording on this to
state
> >that UHMW is only legal on fiberglass.
> >2. UHMW does not need a stop in the head between the shaft and the
> >UHMW. You will not get a punch through with these heads.
> >3. 28 inches is the max length for both arrows and bolts the average
> >bolt length is 16 inches. But this should be adjusted to balance with
your
> >crossbow.
> >
> >Fearghus
> >
> >Wes Duke
> >Systems Analyst
> >
> >wduke at HealthAxis.com
> >817-255-3240
> >Pager 817-418-2612
> >
> >
> >
> >
> > -----Original Message-----
> > From: Pug Bainter [SMTP:pug at pug.net]
> > Sent: Thursday, June 22, 2000 9:34 PM
> > To: ansteorra-archery at ansteorra.org
> > Subject: ARCH - Combat bolt question...
> >
> > Good Morning,
> >
> >   I sat down and read the Participants Handbook tonight. There were
> >many
> >   things I was confused by, not the least of which were in the
> >archery
> >   section.
> >
> >   The three I can think of right now are:
> >
> >   1) I thought UHMW could only be done with fiberglass. It states
> >that
> >      wood is acceptable. Am I just confused?
> >
> >   2) While I understand the need for a stop in the heads, I didn't
> >think
> >      the head in the UHMW arrows I have is a 1 1/4" stop. I thought
> >they
> >      were bored out with a much smaller stop put into them. Am I
> >just
> >      confused?
> >
> >   3) The only mention of length of shafts is of 28". Does this mean
> >both
> >      arrows and crossbow quarrels? That seems a bit odd.
> >
> >   Thanks for clarifying these things!
> >
> > Ciao,
> >
> > --
> > Phelim "Pug" Gervase   | "I want to be called. COTTONTIPS. There is
> >something
> > Bryn Gwlad - Ansteorra |  graceful about that lady. A young woman
> >bursting with
> > Dark Horde Moritu      |  vigor. She blinked at the sudden light.
> >She writes
> > pug at pug.net            |  beautiful poems. When ever shall we meet
> >again?"
> >   Note: The views do not reflect the SCA nor the Kingdom of
> >Ansteorra.
> >
>
>===========================================================================
> =
> > Go to http://lists.ansteorra.org/lists.html to perform mailing list
> >tasks.
>
>===========================================================================
> =
> >Go to http://lists.ansteorra.org/lists.html to perform mailing list
tasks.
> >
>
>
============================================================================
> Go to http://lists.ansteorra.org/lists.html to perform mailing list tasks.

============================================================================
Go to http://lists.ansteorra.org/lists.html to perform mailing list tasks.